1069 results found
    1. Air Classified Milling

      Air Classified Milling

      There are many reasons for milling materials: to increase solubility speed, to combine materials into a fine milled product, to give good 'mouth feel' & taste impact. Air classifier mills can achieve particle size reduction down to 4 to 15 microns. This depends on the mill selection and the characteristics of the material to be milled. Spray dried powders mill finer than crystalline powders. There are principally two types of mill process: mechanical impact milling & air jet milling. In mechanical impact mills, milling is achieved by impact between a high speed rotor fitted with hammers or pins and a stationary grinding track. Contact components are stainless steel. Materials harder than Mohs 3.5 are unsuitable for processing on these mills. Air jet milling uses compressed gas to impact the particles against each other. The advantages are higher energy input thus potentially finer milling and milling of abrasive materials. The disadvantage is often very high energy input for the compressed gas. In both types of mill particle size is controlled using an internal rotating classifier. Cryogenic freezing of raw material can permit milling of tough materials which become brittle when frozen. Depending on the requirements of the process and product temperature, controlled milling is also possible with either cooling of the mill or with introduction of heat into the mill air stream. Some products are sensitive to air oxidation during milling. At Custom Powders Ltd it is possible to run air classifier mills under an inert nitrogen atmosphere. Throughput on these mills is highly dependent on the raw material properties and the final particle size required. With 35 years experience in air classifier milling we can usually make a reasonable estimate for a new product based on historical data. Custom Powders Ltd offer air classified milling in 4 production suites ranging from FSSC22000 food grade, industrial and even to medical grade plastics.

    2. Air classifying

      Air classifying

      Air classifying is suitable for high volume processing where a single product cut is required, to remove oversize or fines, typically between 10 and 300 microns. It is therefore capable of a smaller particle size cut than sieving. The accuracy of cut achieved is very material dependent and requires extended development time. Material is air conveyed into the classifier. This process is best suited to free flowing powders but sometimes it can accommodate cohesive powders. The vigorous air conveying and classifier action makes this process less suitable for hygroscopic or friable materials. Once the material enters the classifier an adjustable but static baffle system combined with variable speed classifier wheel achieves the separation. Fine material passes out of the classifier with the air flow and is separated in a filter unit, from where it can be packed into big bags or sacks. Oversize drops out of the air flow in the classifier and is discharged via a rotary valve. Air classifying is commonly used in Protein Shifting where precise particle size control is essential to provide consistent high protein content in the fine fraction. Air classifying is offered from three process units with standards from industrial to FSSC22000 food grade.

    3. Air Freight

      Air Freight

      Seamless air freight solutions backed by global expertise. Drawing on a vast global network of industry representatives and our team’s extensive experience, we provide seamless, secure and efficient air freight solutions that keep your business moving forward. We understand that timely delivery is critical to your operations, so we prioritise clear communication, proactive problem-solving, and flexible options tailored to your unique shipping requirements. Hazardous cargo undertaken Track and trace Customs brokerage Complete documentation processes High speed delivery Global reach

    4. Air Operated Diaphragm Pumps

      Air Operated Diaphragm Pumps

      Empire Pumps’ extensive range of Air Operated Diaphragm Pumps commonly known as AOD or AODD Pumps, are specifically designed for durability, performance and reliability. The pumps robust construction gives the ability to transfer abrasive and highly viscous solutions, manufactured for use with many industries including chemical, pharmaceutical, wastewater, effluent treatment, metal finishing and many more. Our air driven pump range vary in size from ¼’’ to 3’’ achieving flow rate capabilities up to 1000 l/min, making them ideal for a variety of chemical transfer applications. Equipment materials of construction are available in polypropylene, PVDF, aluminium and stainless steel. Elastomer, diaphragm materials: Santoprene, Nitrile, EPDM, Viton and Teflon (PTFE). Our range of Air Operated Double Diaphragm Pumps offer technical benefits when considering the corrosive nature of the chemistries being transferred. The air valve and centre section of our pneumatic pump range is plastic opposed to aluminium. Non-metallic constructed parts are more corrosive resistant should chemicals reach the centre section of the pump. Furthermore, our pump design utilises bolts opposed to band clamps, ensuing more support to the full surface area of the diaphragms whilst the pump is in operation. The bolted design also provides easier maintenance on strip down and assembly of the pump. Our pump design offers a centre positioned inlet and outlet port, giving equal flow through each side of the pump. This design feature enables our pump range to achieve 15 to 20% increased flow rate for the equivalent pump size of an alternative manufacturer.

    5. Alpha WA Chlorine Dioxide Generator

      Alpha WA Chlorine Dioxide Generator

      From healthcare estates to food processing, industrial plants and commercial buildings, the Alpha WA Chlorine Dioxide Generator is engineered for performance and uptime. Proportional control from a pulsed water meter tracks real-time flow maintains consistent chlorine dioxide (ClO2) residuals – no guesswork, no overdosing. An in-line reaction chamber generates ClO2 on demand, avoiding bulk storage and reducing risks to operators and the environment. Its small footprint and straightforward installation minimise downtime and keep sites compliant and operational. The Alpha WA integrates with industry-standard onsite BMS for centralised automation and alarm handling. Paired with 5G Scotmas Insite, users gain live dashboards, trend plotting, comprehensive data logging, and actionable notification to support compliance. With multiple safety interlocks, the Alpha WA provides tighter dosing control, clearer performance data, and dependable ClO2 delivery directly to the main line or storage tank.

    6. AMI-II LINETOC Compact Analyser

      AMI-II LINETOC Compact Analyser

      The AMI-II LineTOC Compact comes with a small footprint and features an optional stainless-steel protective cover. It ensures precise, continuous TOC measurement in ultrapure water. Designed for pharmaceutical, semiconductor, and high-purity water applications, this reagent-free system uses conductivity differential before and after UV oxidation for fast trend identification. The AMI-II LineTOC Compact supports compliance with FDA 21 CFR Part 11 and all known pharmacopeias with automatic SST and comprehensive validation documentation. The reliable analyser is easy to operate and offers the perfect solution to replace costly lab analysis.

    7. Amphoterics range

      Amphoterics range

      The dipropionates are generally available as the mono alkali metal salt, and the monopropionate as the free acid. The dipropionates are used in many cleaning systems specifically for their solubilisation and detergent properties. Some of the the many advantages dipropionates offer are: ■ Excellent dirt lifting properties, which makes them an essential component of hard surface cleaners and vehicle cleaners, particularly when applied by pressure washer. ■ Excellent hydrotropic properties, which enables the use of nonionic surfactants in aggressive conditions eliminating the use of traditional hydrotropes. The amphoterics elevate the cloud points of alkaline and highly built detergent systems, thus improving their detergency at high operating temperatures. ■ They impart excellent free rinsing properties to detergent systems leaving a smear free surface. This is an important consideration for all forms of industrial and household cleaning. ■ As dipropionates are salt free they do not promote the corrosion of metal surfaces. In fact they exhibit good anti-corrosive properties for ferrous metals. ■ They are stable across the whole pH range and confer stability to other more traditional surfactant systems, thus giving added versatility. ■ They have low orders of toxicity and are therefore ideal for cleaning surfaces which come into contact with food. ■ They are stable in hard water and can impart stability to other surfactants when formulated into products used in hard water areas. ■ High foaming or low foaming amphoterics available, depending on the formulators requirement.